upvc Elbow 2″ 45* GM Local

Description

upvc Elbow 2″ 45*

 

GM made in Pakistan ASTM uPvc Sch-40 plumbing building materials distributor, dealer, suppliers in Karachi Pakistan contact 0322-3540656

 

What is upvc Elbow 2″ 45* GM Local ?

 

The UPVC Elbow 2″ ¹$45^\circ$ GM Local is a specific type of pipe fitting used in plumbing, particularly where a gentle change in direction is required.² The details below are typical for this product category, recognizing that “GM Local” indicates a generic or locally-manufactured brand, which may have slight variations in specific thickness or pressure rating compared to fittings strictly adhering to international standards.

1. Description and Specification upvc Elbow 2″ 45* GM Local

This is a plastic fitting made from Un plasticized Polyvinyl Chloride (UPVC), designed to connect two pipes of the same size at a ³$45^\circ$ angle.⁴

Feature	Detail
Name	UPVC Elbow
Size	2 inches (Nominal Diameter)
Angle	$\mathbf{45^\circ}$ (Degrees)
Material	UPVC (Un plasticized Polyvinyl Chloride)
Function
Connection Type	Typically “Slip” or “Solvent Weld” sockets on both ends, meaning the pipe slides in and is secured with solvent cement.
Color	Commonly White or Grey.
Rating (Common)	Used for both pressure (cold water supply) and non-pressure (drainage, irrigation) applications, depending on the pipe’s schedule (e.g., Schedule 40 or PN-rated).
“GM Local”	Denotes a Generic Make product manufactured to meet local (regional) market needs and standards.
Key Properties	Lightweight, excellent resistance to chemicals, corrosion, and rust, non-toxic (often lead-free, but confirm for potable water use), and easy to install.

3. Usage and Application

The ²³$45^\circ$ angle is preferred over ²⁴$90^\circ$ for certain applications to promote smoother flow.²⁵

• Drainage, Waste, and Vent (DWV) Systems: The $45^\circ$ angle is often used in drainage systems to create a sweeping turn. This is crucial as it helps prevent clogs and allows solids to pass easily, ensuring better performance than a sharp right angle.
• Irrigation and Water Distribution: Ideal for main or sub-main distribution lines to gently route water around obstacles, ensuring a more consistent flow rate throughout the system.²⁶
• Structure and Non-Fluid Applications: Sometimes used for lightweight construction or frame-building projects (often in a “furniture grade” variation), as UPVC is easy to cut and assemble.

Step-by-Step Installation

 

1.  Cut the UPVC pipe to the required length, ensuring the cut is perfectly square (¹⁰$\mathbf{90^\circ}$) to maximize the bonding surface area.¹¹
2.  Wipe down the end of the pipe and the inside of the elbow socket with a clean rag to remove all dirt and moisture.
3.  Insert the pipe into the elbow socket without cement to confirm a snug fit. It should go in about one-third of the way. Mark the pipe and the fitting to ensure correct rotational alignment when you apply the cement.
4.   The primer softens the UPVC surface for the solvent cement. Follow the primer manufacturer’s drying time (usually just a few seconds).
5. solvent cement to the same surfaces.¹⁵ Work quickly, as the cement is fast-acting.
6.   quarter-turn twist as you push.¹⁷ The twist helps spread the cement evenly.¹⁸ Push the pipe until it is fully seated against the stop inside the fitting.
7. Hold the joint firmly for at least ¹⁹$\mathbf{30}$ seconds to prevent the pipe from pushing back out.²⁰ Wipe off any excess cement.²¹ Allow the joint to cure completely according to the solvent cement manufacturer’s directions (this can range from 15 minutes to 24 hours before pressurizing the system).²²