PPR Pipe 75mm EG euro gulf

Description

PPR Pipe 75mm 

 

EG PPRc pipes and fittings local ,, Food Grade, Plumbing Materials, Manufacturer Suppliers in Karachi Pakistan  Contact 0321-2248975,

 

What is PPR Pipe 75mm EG euro gulf ?

 

PPR 75 mm PN 20 Euro Gulf pipe is a PP‑R (polypropylene random copolymer) pressure pipe designed for high‑pressure hot and cold water and HVAC/chilled/hot water systems, typically in buildings and light industry. It is part of the EG PPR‑C system made by Euro Gulf, usually in green color, with a design life of about 50 years when used within its rated pressure and temperature limits.

 description PPR Pipe 75mm EG euro gulf

• Material: PP‑R / PPR‑C plastic, hygienic and suitable for potable water and food‑related applications.

• Nominal diameter: 75 mm outside diameter; PN 20 means 20 bar nominal pressure at 20 °C with corresponding wall thickness (about 12.5 mm in typical PN 20 75 mm pipes).

• Applications:

  • Hot and cold water distribution in houses, apartments, and commercial buildings.

  • HVAC: hot water, chilled water and AC/refrigeration water circuits.

  • Compressed air and some industrial/aggressive fluids (within chemical resistance limits).

Main specifications (typical)

For a 75 mm PN 20 PPR pipe in this class (values are typical for standard PN 20 products; always confirm with the exact Euro Gulf datasheet):

• Outside diameter: 75 mm.

• Wall thickness: around 12.5 mm for PN 20 in 75 mm size (this gives higher pressure rating and temperature resistance).

• Pressure rating: PN 20 → 20 bar (2.0 MPa) at 20 °C; used for high‑pressure water, high‑rise and HVAC systems where PN 16 is not sufficient.

• Temperature range (general PPR PN 20):

  • Cold water: 0–25/30 °C up to full PN 20 rating.

  • Hot water/heating: continuous service around 70 °C with derated pressure, short‑term peaks up to about 90–95 °C depending on manufacturer curves.

• Standards: EG PPR‑C systems are designed according to DIN 8077/8078 and relevant drinking‑water and building piping standards.

• Service life: design life ~50 years when installed and operated within the specified pressure/temperature envelope.

Key features for HVAC and water

• Corrosion‑free: No rust or scaling, unlike steel or GI pipes, which keeps internal diameter and flow capacity stable.

• Smooth bore: Very low friction, good flow, lower pump head loss, and reduced noise in high‑velocity HVAC circuits.

• Thermal properties: Lower thermal conductivity than metal, so reduced heat loss in hot water and heat gain in chilled water lines (still usually combined with insulation).

• Hygienic and non‑toxic: Safe for drinking water and food/beverage processing, with no taste or odor.

• Fusion jointing: Socket fusion gives monolithic, leak‑free joints; the joint is as strong as the pipe wall when done correctly.

• Range: EG PPR‑C system includes fittings and valves up to at least 110 mm, which allows full systems including flange adaptors and valves on large diameters.​

Installation guidelines (practical points)

For 75 mm PN 20 EG PPR‑C in HVAC and hot/cold water:

• Jointing method:

  • Use socket fusion (polyfusion) with the manufacturer‑recommended welding machine and dies for 75 mm.

  • Respect heating time, insertion depth and cooling time specified for 75 mm PN 20 (overheating or underheating causes weak joints or bore reduction).

• Pipe preparation:

  • Cut pipe square with a suitable cutter.

  • Clean and dry pipe and fitting inside/outside before fusion; avoid oil, dust and moisture.

• Alignment and support:

  • Align joints carefully; avoid torsion while cooling.

  • Provide supports/cleats at recommended spacing for 75 mm (PPR needs more supports than steel because of creep and expansion).

• Thermal expansion:

  • Allow for expansion loops, offsets or sliding supports especially in hot water and heating mains; PPR has higher linear expansion than metal.

  • Use fixed points only at strategic locations (e.g., near risers, branches, equipment).

• Testing and flushing:

  • After installation and cooling of all joints, pressure‑test the system (usually 1.5 × operating, within PN 20 limit) according to standard practice and Euro Gulf recommendations.

  • Flush lines before commissioning to remove debris.

• Protection:

  • For outdoor or UV‑exposed sections, protect with insulation, cladding or sleeves; plain PPR is not UV‑resistant long‑term.

  • Avoid direct contact with sharp edges or concentrated loads that can notch the pipe.

Typical usage scenarios

• Building hot and cold water risers and mains where static pressure or pump pressure is high (high‑rise, booster pump systems) and PN 16 may be marginal.

• HVAC:

  • Hot water supply/return for heating coils and AHUs.

  • Chilled water distribution in small to medium systems where PPR is acceptable (temperature typically 5–15 °C with proper insulation).

• Industrial: process water, some chemicals and compressed air lines, provided the fluid is compatible with PP‑R and temperature/pressure are within PN 20 limits.