Euro Gulf upvc End Cap 6″

Description

upvc End Cap 6″

 

Euro Gulf local Distributor Suppliers in Karachi Contact 0321-2248975 ASTM uPvc Sch-40 Pressure Fittings, Drain sewer ventilation

 

What is Euro Gulf upvc End Cap 6″ ?

 

The Euro Gulf uPVC End Cap 6″ SCH 40 is a plumbing fitting manufactured by Euro Gulf Industries (Pvt.) Ltd., a Pakistani company specializing in polymer pipes and fittings (including uPVC, PPR-C, PE, and cPVC). Their official website is eurogulf.com.pk, where they list uPVC pressure pipes and fittings.

This end cap is part of their uPVC Schedule 40 (SCH 40) fittings line, compliant with ASTM D2466 standards for socket-type (slip/solvent weld) pressure fittings.

Description

It is a socket-end cap (also called slip cap or end plug) made from Un plasticized Polyvinyl Chloride (uPVC). The cap seals the end of a 6-inch nominal diameter SCH 40 uPVC pipe, creating a permanent, leak-proof closure. It has a slip (socket) connection that fits over the pipe end. Typically white in color, it is lightweight, corrosion-resistant, non-toxic, and designed for pressurized systems.

Specifications

• Material: uPVC (Un plasticized Polyvinyl Chloride), high-quality, rigid, and durable.
• Size: 6 inch (nominal diameter; actual outer diameter of compatible pipe is approximately 6.625 inches / 168.3 mm).
• Schedule: 40 (SCH 40) — standard wall thickness for pressure applications.
• End Type: Slip/Socket (solvent cement weld / SC/J type).
• Standards: ASTM D2466 (for PVC pressure fittings); often meets NSF/ANSI for potable water in similar products.
• Maximum Operating Temperature: 140°F (60°C) — suitable for cold water; not recommended for continuous hot water above this limit.
• Pressure Rating: Typically up to 150 PSI at 73°F (23°C) for SCH 40 PVC systems (de-rates with higher temperatures); exact rating depends on system design.
• Color: Usually white.
• Applications Compliance: Designed for pressure piping systems.

Usage

This end cap is used to permanently or temporarily seal the open end of a uPVC SCH 40 pipe run. Common applications include:

• Terminating pipe ends in cold water supply lines.
• Closing off branches or unused sections in plumbing networks.
• Sealing for pressure testing or system isolation.
• In HVAC systems (e.g., chilled water lines, condensate drains, or low-pressure ducting support — note: uPVC SCH 40 is common for non-hot fluid HVAC piping).
• Hot and cold water supply — primarily for cold water (potable, irrigation, chilled water); limited suitability for hot water due to the 60°C max temperature (use cPVC or other materials for higher hot water temps).
• Other: Irrigation, pool/spa, industrial low-pressure lines, or drainage where pressure resistance is needed.

It provides excellent chemical resistance, no rust/corrosion, long service life, and hygienic properties (non-toxic for potable water when certified).

Installation

Installation is straightforward using solvent cement welding (no threads or mechanical tools needed beyond cutting/priming):

1. Prepare the pipe: Cut the 6″ SCH 40 uPVC pipe squarely and cleanly. Deburr and bevel the edge slightly.
2. Clean surfaces: Wipe the pipe end and the inside of the cap socket with a clean cloth to remove dirt, oil, or moisture.
3. Apply primer: Use PVC primer on both the pipe end and the cap socket (required for proper bonding).
4. Apply solvent cement: Quickly apply PVC solvent cement (appropriate for pressure fittings) to the pipe end and socket interior.
5. Assemble: Immediately push the cap fully onto the pipe end with a quarter-turn twist for even distribution. Hold firmly for 10-30 seconds to set.
6. Cure: Allow full curing time (typically 15-60 minutes before pressure testing; longer in cold conditions) per cement manufacturer instructions.
7. Test: Pressure test the system as needed.