Euro Gulf upvc Elbow 2″ 45*

Description

upvc Elbow 2″ 45*

 

Euro Gulf local Manufacturer Suppliers in Karachi Contact 0321-2248975 ASTM uPvc Sch-40 Pressure Fittings, Drain sewer ventilation

 

What is Euro Gulf upvc Elbow 2″ 45* ?

 

Euro Gulf uPVC Elbow 2″ 45° (Sch-40 Pressure Fitting) is a molded un plasticized polyvinyl chloride (uPVC) fitting manufactured by Euro Gulf (a common brand in Pakistan and the Middle East, often supplied alongside brands like AGM, Pak Arab, or United Gulf). It changes the direction of flow by 45 degrees in piping systems.

Description

This is a slip x slip (socket x socket) elbow designed for solvent cement (glue) jointing with 2-inch nominal Schedule 40 uPVC pipe. It features a smooth interior to minimize friction and flow resistance, and it is typically white or light gray in color. The fitting is injection-molded for uniformity and durability.

It belongs to the ASTM D2466 standard for PVC pressure fittings (Schedule 40), which ensures compatibility with Sch-40 pressure pipes.

Key Specifications

• Size: 2 inch nominal (fits 2″ Sch-40 uPVC pipe; actual OD of pipe is approximately 2.375 inches).
• Angle: 45 degrees.
• Type: Slip x Slip (socket ends for solvent welding).
• Schedule: Sch-40 (thicker walls than thin-wall DWV fittings, suitable for moderate pressure).
• Material: uPVC (Un plasticized Polyvinyl Chloride) – rigid, lead-free, corrosion-resistant.
• Standards: ASTM D2466 (for Sch-40 PVC fittings); often NSF/ANSI 14 or 61 compliant for potable water in similar products.
• Pressure Rating: Approximately 280 PSI at 73°F (23°C) for water (non-shock); derates with temperature (e.g., lower at higher temps, max service temp typically 140°F / 60°C). Not for compressed air/gas or hot water above rating.
• Temperature Range: Suitable for cold water and up to ~60°C (140°F); not recommended for hot water lines.
• Dimensions (approximate for standard Sch-40 45° elbow; exact may vary slightly by manufacturer):
  • Center-to-end (H/J): ~2-1/16 inches (one leg) to ~2-3/4 inches overall span.
  • Socket depth and ID match 2″ Sch-40 pipe.
• Weight: Lightweight (~0.3–0.4 lbs per fitting).
• Jointing: Solvent cement (primer + PVC cement) for permanent, leak-proof bonds.
• Color: Usually white.

Note: Sch-40 pressure fittings have thicker walls and higher pressure capability than pure DWV (drain-waste-vent) fittings, though both can handle gravity drainage. Always match with Sch-40 pipe for pressure systems.

Usage and Applications

The Euro Gulf 2″ 45° Sch-40 uPVC elbow is versatile and commonly used in:

• Pressure systems: Cold water supply, irrigation, sprinkler systems, swimming pools, chilled water lines, and low-pressure industrial fluid transport (e.g., chemicals compatible with uPVC).
• Drain, Sewer, and Ventilation (DWV): Wastewater drainage, soil stacks, vent pipes, and sewer lines where a gentler 45° bend (vs. 90°) reduces clogging risk, improves flow, and allows smoother transitions around obstacles. The 45° angle minimizes turbulence compared to sharper elbows.
• Other common uses: Plumbing in residential/commercial buildings, HVAC condensate drains, underground installations, and agricultural piping. It is ideal where corrosion resistance, chemical inertness, and lightweight installation are needed (no rust, scaling, or electrolysis issues).

Advantages:

• Corrosion and chemical resistant.
• Easy, fast solvent-weld installation (no threading or heat fusion needed).
• Smooth bore for better flow and lower friction loss.
• Cost-effective and long-lasting (decades in proper use).
• Eco-friendly and recyclable in many regions.

Installation Notes:

• Cut pipe square, deburr, clean, apply primer then cement, and insert fully while rotating slightly. Hold for a few seconds.
• Use with matching 2″ Sch-40 uPVC pipe.
• Support pipes properly to avoid stress on fittings.
• Not for high-temperature or high-pressure steam/compressed gas applications.