AGM upvc Tee 8″

Description

upvc tee 8″

 

AGM imported from Saudi Arab ASTM uPvc Sch-40 Pressure Fittings, Drain sewer ventilation. imported material in Karachi Pakistan 0322-3540656

 

What is AGM upvc Tee 8″ ?

 

The AGM uPVC Tee 8″ Sch 40 is a T-shaped pipe fitting manufactured by Arabian Gulf Manufacturers Ltd. (AGM), a leading Saudi Arabian company based in Jeddah. AGM produces high-quality uPVC (un plasticized polyvinyl chloride) pipes and fittings, often imported to regions like Pakistan for plumbing applications.

This fitting creates a 90-degree branch in piping systems. It features three socket ends for solvent welding to 8-inch Schedule 40 uPVC pipes. Sch 40 uPVC is rigid, lightweight, corrosion-resistant, and suitable for both pressure and non-pressure applications.

AGM products comply with international standards such as ASTM D1785 (for pipes) and ASTM D2466 (for fittings), as well as Saudi standards (SASO). They are commonly white or gray and designed for durability in harsh environments.

Specifications

• Nominal Size: 8 inches (203.2 mm outside diameter for Sch 40 pipe).
• Schedule: 40 (wall thickness approx. 0.322 inches / 8.18 mm for compatible pipe).
• Material: uPVC (Rigid PVC, Type 1, Grade 1, cell classification 12454 per ASTM D1784).
• Standards: ASTM D2466 (fittings), ASTM D1785 (compatible pipes), often NSF-certified for potable water.
• Pressure Rating: Suitable for systems up to ~120-180 psi (depending on temperature; max service temp ~140°F/60°C).
• Joint Type: Socket (slip) ends for solvent cement welding.
• Color: Typically white (for pressure/water supply) or gray.
• Weight/Dimensions: Large fitting; center-to-end dimensions follow ASTM tables (approx. 7-8 inches lay length per branch for 8″ size).

These fittings resist chemicals, abrasion, and corrosion, with smooth inner walls for good flow.

Usage

This tee suits:

• Water Supply: Potable cold water distribution (pressure systems), irrigation.
• Sewerage & Drainage: Non-pressure or low-pressure sewer, waste, vent, and drain lines (including HVAC/AC drain).
• Industrial: Chemical lines (resistant to many acids/bases), underground ducts.
• Ideal for residential, commercial, and industrial plumbing where moderate pressure and chemical resistance are needed.

Not recommended for hot water (use CPVC instead) or high-pressure beyond Sch 40 ratings.

Installation

uPVC Sch 40 fittings like this AGM Tee use solvent cement welding (chemical fusion) for leak-proof joints stronger than the pipe itself.

Step-by-Step Guidelines:

1. Cut Pipe: Use a pipe cutter or fine-tooth saw for a square cut. Deburr and chamfer (15° bevel) the pipe end to remove burrs and ease insertion.
2. Dry Fit & Mark: Insert pipe into fitting sockets to check fit and mark insertion depth.
3. Clean Surfaces: Wipe pipe ends and fitting sockets with a clean cloth. Use uPVC primer/cleaner to remove dirt, oils, and gloss.
4. Apply Solvent Cement:
   • Use appropriate uPVC cement (per ASTM D2564).
   • Apply a thin, even coat to pipe end first, then a heavier coat inside the fitting socket.
   • Work quickly—cement sets fast.
5. Assemble: Immediately insert pipe fully into socket (bottom out), then quarter-turn (90°) to distribute cement evenly. Hold for 30-60 seconds.
6. Cure: Wipe excess cement. Allow joint to set (10-30 minutes initial; full cure 24 hours before pressure testing). Avoid disturbance.
7. Safety/Tips:
   • Work in ventilated area; cement is flammable.
   • For large 8″ sizes, use helpers for alignment.
   • Do not install in wet/rainy conditions or extreme cold (<5°C).
   • Test system hydrostatically after full cure.