Description
Cpvc Elbow 1″ 45* AGM
Cpvc for hot water, AGM imported from Saudi Arab. Schedule 80 materials for high pressure and hot water supplier contact 0322-3540656
What is AGM cpvc Elbow 1″ 45* ?
Specifications
The following table outlines the key specifications for the AGM CPVC Elbow 1″ 45°:
| Parameter | Details |
|---|---|
| Size | 1 inch (nominal diameter, CTS – Copper Tube Size compatible) |
| Angle | 45 degrees |
| Material | CPVC (Chlorinated Polyvinyl Chloride), cell class 23447-B |
| Color | Light gray |
| Connection Type | Socket ends (solvent weld) |
| Pressure Rating | Up to 20 bar (290 PSI) at 93°C (200°F); derates with higher temperatures (e.g., 100 PSI at 180°F typical for hot water) |
| Temperature Range | 32°F to 200°F (0°C to 93°C); suitable for continuous hot water exposure up to 180°F |
| Standards | ASTM F437 (socket fittings) and ASTM F439 (CPVC fittings); NSF 14 and 61 certified for potable water; SASO approved for Saudi market |
| Dimensions (approx.) | Outer diameter (socket): ~34-35 mm; Insertion length: ~23 mm; Weight: ~0.1-0.15 kg |
| Certifications | Corrosion-resistant, chemical-resistant; UL/FM listed equivalents for fire-rated applications if specified |
These specs ensure the elbow can handle high-pressure hot and cold water flows while maintaining structural integrity over time.
Installation
Installing the AGM CPVC Elbow 1″ 45° involves a straightforward solvent welding process, which creates a strong, permanent bond. Follow these steps for safe and effective installation:
- Preparation: Cut CPVC pipes squarely using a pipe cutter or fine-tooth saw. Bevel the edges lightly with a deburring tool to remove sharp burrs. Ensure all surfaces are clean and dry—wipe away dust, grease, or moisture.
- Dry Fit: Test-assemble the elbow with the pipes to verify alignment and measurements. The socket ends should slide over the pipe ends by about 3/4 to 1 inch (20-25 mm) for a proper fit.
- Apply Primer and Cement: Use a CPVC-specific primer (purple for visibility) applied liberally to both the pipe exterior and the socket interior using a dauber. Immediately follow with CPVC cement (one-step, no primer in some cases, but primer is recommended for AGM products). Apply a full, even layer to the pipe end and a lighter layer inside the socket. Avoid over-application to prevent drips.
- Assembly: Quickly insert the pipe into the socket with a twisting motion (1/4 turn) while pushing firmly for full insertion. Hold in place for 30 seconds to set. Align the fitting immediately, as the joint sets in 15-30 seconds and cannot be adjusted after.
- Curing: Allow curing time based on ambient temperature (e.g., 15 minutes at 80°F/27°C; longer in cooler conditions). Do not pressure-test until fully cured (typically 24 hours for full strength).
- Safety Notes: Work in a well-ventilated area, wear gloves and eye protection. Use only CPVC-rated primers and cements—do not mix with PVC types. Avoid installation in direct sunlight or extreme cold, as it affects curing. For threaded adapters, use thread sealant tape rated for CPVC.
Professional installation is recommended for pressurized systems to comply with local plumbing codes.
Usage
This elbow is primarily used in hot and cold potable water distribution systems, where it redirects flow at a 45° angle to optimize space and reduce turbulence compared to sharper bends. Key applications include:
- Hot Water Supply: Ideal for residential and commercial hot water lines (e.g., showers, sinks, boilers) due to its high-temperature tolerance, preventing degradation from heated water up to 180°F.
- Potable Water Systems: NSF-certified for safe drinking water transport, resistant to scaling and bacterial growth.
- HVAC and Radiant Heating: In heating/cooling loops for efficient fluid direction without pressure loss.
- Industrial/Process Lines: For deionized water, chilled water, or mild chemical transport in plating, processing, or wastewater treatment (avoid compressed air/gases).
- Fire Sprinkler Systems: Compatible with light-hazard setups under NFPA standards, though confirm local AHJ approval.
Reviews
There are no reviews yet.