AGM cpvc Elbow 1/2″ 45*

Description

Cpvc Elbow 1/2″ 45* AGM 

 

Cpvc for hot water, AGM imported from Saudi Arab. Schedule 80 materials for high pressure and hot water till 93  from 1/2″ to 2″ sizes  0322-3540656

 

What is AGM cpvc Elbow 1/2″ 45* ?

 

The AGM CPVC Elbow (1/2″ 45-degree) is a plumbing fitting designed for hot water applications, manufactured by AGM (likely referring to a brand like AGM Pipes or a similar entity in the Middle East). It’s imported from Saudi Arabia, where CPVC pipes and fittings are produced by companies such as Saudi Arabian Pipes Company (SAPCO) or equivalents, adhering to international standards like ASTM for durability in high-temperature environments. This elbow is used to change pipe direction at a 45-degree angle in hot water systems, offering corrosion resistance and ease of installation compared to metal alternatives.

Description

• Material: Chlorinated Polyvinyl Chloride (CPVC), a thermoplastic polymer modified for higher heat resistance. It’s rigid, lightweight, and non-conductive, making it ideal for hot water plumbing.
• Design: A 45-degree elbow fitting with a 1/2-inch nominal pipe size (NPS), featuring threaded or solvent-weld ends for secure connections. The 45-degree angle allows for gradual directional changes, reducing flow turbulence and pressure drops compared to sharper 90-degree elbows.
• Key Features:
  • Suitable for hot water up to 93°C (200°F) continuously, with short-term peaks up to 100°C (212°F).
  • Corrosion-resistant to chemicals, minerals, and scaling common in water systems.
  • Imported from Saudi Arabia, often meeting ISO 15877 standards for plastic piping systems.
  • Lightweight (typically 0.1-0.2 kg per piece) and easy to handle.
  • Available in various colors (e.g., white or gray) for easy identification in plumbing setups.
• Common Applications: Residential and commercial hot water lines, such as in showers, sinks, boilers, and radiant heating systems. Not recommended for potable water unless certified (check local regulations).

Specifications

Based on standard CPVC fitting specs (e.g., ASTM D2846 for CPVC compounds and ASTM F439 for fittings), here’s a breakdown:

• Size: 1/2″ (nominal diameter, actual OD ~21.3 mm, ID ~15.9 mm).
• Angle: 45 degrees.
• Pressure Rating: Up to 1,000 psi (6.9 MPa) at 23°C, decreasing with temperature (e.g., 400 psi at 82°C).
• Temperature Range: -18°C to 93°C (0°F to 200°F) for continuous use.
• Dimensions:
  • Length: Approximately 50-60 mm (center-to-end).
  • Wall Thickness: 2.5-3 mm, ensuring structural integrity.
• Connection Type: Solvent-weld (glue) or threaded (NPT for threaded versions).
• Standards Compliance: ASTM F439, ISO 15877, and often Saudi Arabian Standards Organization (SASO) certified for import.
• Packaging: Typically sold in packs of 10-50, with labels indicating manufacturer (e.g., AGM), origin (Saudi Arabia), and batch details.
• Weight: ~50-100 grams per fitting.
• Shelf Life: Indefinite if stored in a cool, dry place away from UV light.

Note: Exact specs may vary by batch; always refer to the product label or manufacturer’s datasheet for precise details.

Installation

CPVC fittings like this are straightforward to install, requiring basic plumbing tools. Follow these steps for safe, leak-free setup (based on general CPVC installation guidelines from ASTM and manufacturer recommendations):

1. Preparation:

   • Ensure pipes and fittings are clean, dry, and free of debris.
   • Cut CPVC pipes square using a pipe cutter or hacksaw. Deburr edges with a file or sandpaper.
   • Measure and mark the pipe for the elbow’s insertion depth (typically 1-1.5 cm into the fitting).

2. Priming and Cementing (for Solvent-Weld):

   • Use CPVC-specific primer and cement (e.g., from the same brand to ensure compatibility).
   • Apply primer to both pipe and fitting ends, then cement immediately.
   • Insert pipe into the elbow fully and twist 1/4 turn to distribute cement evenly.
   • Hold for 30-60 seconds until set; full cure takes 24 hours.

3. Threaded Installation (if applicable):

   • Apply Teflon tape or pipe dope to threads.
   • Screw the elbow onto threaded pipes or adapters, tightening with a wrench (avoid over-tightening to prevent cracking).

4. Support and Testing:

   • Support pipes every 1-2 meters to prevent sagging.
   • Pressure-test the system at 1.5x working pressure for 30 minutes to check for leaks.
   • Operate at full hot water temperature gradually to avoid thermal shock.

Safety Tips: Wear gloves and eye protection. Work in a well-ventilated area as cement fumes are toxic. Ensure the system is depressurized before installation. Consult local plumbing codes (e.g., UPC or IPC) for hot water systems.

Usage

• Primary Use: Directing hot water flow in residential or commercial plumbing, such as connecting pipes in under-sink units, water heaters, or solar hot water systems. The 45-degree angle minimizes flow resistance, ideal for gradual bends in tight spaces.
• Advantages Over Alternatives: Better heat tolerance than PVC (which is for cold water only), and more cost-effective and easier to install than copper or PEX in hot water apps.
• Maintenance: Inspect periodically for leaks or wear. Clean with mild soap; avoid harsh chemicals. Replace if exposed to extreme temperatures or UV light.
• Limitations: Not for outdoor use without UV protection, and incompatible with certain solvents or oils. For potable water, ensure NSF/ANSI 61 certification.
• Expected Lifespan: 50+ years under normal hot water conditions, based on CPVC’s proven durability in plumbing (e.g., used in millions of installations worldwide).