AGM upvc Tee 3″

Description

upvc Tee 3″

 

AGM imported from Saudi Arab ASTM uPvc Sch-40 Pressure Fittings, Drain sewer ventilation. imported material in Pakistan contact 0322-3540656

 

What is AGM upvc Tee 3″ ?

 

An AGM UPVC Tee is a pipe fitting shaped like the letter “T” used to connect three sections of UPVC pipe at 90° angles — one inlet and two outlets — to branch or join piping systems. The 3″ SCH 40 designation refers to its nominal diameter (3 inches) and Schedule 40 wall thickness, suitable for pressure and non-pressure applications. These fittings are typically socket-type (smooth sockets to insert pipes).

Brand & Origin:

• AGM (Arabian Gulf Company) quality UPVC fitting.

• Imported from Saudi Arabia — commonly found in plumbing supplies in Pakistan and GCC markets.

---

✅ 2. Material & Standards

Material:

• UPVC – Un plasticized Polyvinyl Chloride

  • A rigid, durable thermoplastic that is chemically resistant, lightweight, and non-toxic for potable water.

Applicable Standards:

• ASTM D2466 — Standard for Schedule 40 PVC plastic pipe fittings (pressure applications).

• Often also compatible with ASTM D2665 for drainage and sewer system branches.

These standards ensure consistent dimensions, strength, and performance to work with other UPVC components.

---

✅ 3. Description & Key Features

Physical Characteristics:

• Nominal Size: 3 inches

• Wall Thickness: Schedule 40 (medium thickness for strength & durability)

• Color: White (typical for UPVC plumbing fittings)

• Ends: Socket/Female sockets for solvent-weld connection.

Key Properties:
✔ Corrosion and rust-resistant
✔ Smooth internal surface for low friction flow
✔ Lightweight, easy to handle
✔ Long service life
✔ Good mechanical strength
✔ Non-toxic — safe for potable water distribution

---

✅ 4. Specifications (Typical)

Note: Actual pressure ratings vary by manufacturer but Schedule 40 generally provides moderate strength for water supply up to typical domestic pressures.

---

✅ 5. Installation Guide

Installation of UPVC fittings like a tee is usually done by solvent welding, sometimes called cold welding:

🔹 Tools & Materials

• UPVC pipes & AGM Tee 3″ SCH40

• UPVC cleaner/primer (if required)

• UPVC solvent cement

• Cutter / fine-tooth saw

• Measuring tape

• Gloves & safety glasses

🔹 Step-by-Step

1. Prepare the Pipe Ends

   • Cut the pipe ends squarely.

   • Remove burrs and rough edges.

   • Lightly chamfer/polish for easier insertion.

2. Dry Fit

   • Fit pipe into the tee socket without cement to ensure alignment and fit.

3. Apply Primer (Optional where required)

   • Brush a thin coat of primer on pipe end and inside the tee socket.

4. Solvent Cement Application

   • Apply even coat of UPVC solvent cement to both the outside of pipe end and inside the tee socket.

5. Assembly

   • Insert pipe quickly and twist a quarter turn to spread the cement evenly.

   • Hold the joint for ~30 seconds until it grips.

6. Curing

   • Allow the solvent cement to cure fully before pressurizing the system (curing time varies with temperature).

7. Support

   • Provide adequate clamps or hangers to support the pipe and fittings.

---

✅ 6. Uses & Applications

🚰 Water Supply

• Branching cold potable water lines

• Connecting main line to secondary lines in residential, commercial plumbing.

🛁 Sewerage & Drainage

• Creating junctions in drainage, waste, and vent (DWV) systems.

• Works in sewer mains where pressure and drainage can coexist.

🌿 Other Common Uses

• Irrigation distribution

• HVAC drain connections

• General civil plumbing networks

• Rainwater systems

---

✅ 7. Advantages of AGM UPVC Fittings

✔ Tough and reliable with good impact resistance
✔ Corrosion and chemical resistance
✔ Easy and fast installation with solvent welding
✔ Lightweight design reduces labor effort and installation cost
✔ Compatible with standard UPVC pipe and fittings
✔ Long life with minimal maintenance required