AGM cpvc Tee 1-1/4″

Description

 cpvc Tee 1-1/4″ AGM

 

AGM Cpvc for hot water, imported from Saudi Arab. Schedule 80 materials for high pressure and hot water till 93 degree importer contact 0322-3540656

 

What is AGM cpvc Tee 1-1/4″ ?

 

Description

AGM CPVC Tee (1-1/4″) is a T-shaped fitting made from Chlorinated Polyvinyl Chloride (CPVC), a thermoplastic material designed for plumbing applications. The tee allows for branching pipes at 90-degree angles, commonly used in residential, commercial, or industrial hot water distribution lines. It’s lightweight, durable, and suitable for potable water systems, with a focus on longevity in environments with fluctuating temperatures.

Specifications

• Material: Chlorinated Polyvinyl Chloride (CPVC), ASTM D1784 compliant.
• Size: 1-1/4 inch nominal pipe size (NPS), with internal diameter approximately 1.38 inches (35 mm) and external diameter around 1.66 inches (42 mm), depending on schedule (typically Schedule 80 for hot water).
• Pressure Rating: Up to 100 psi (pounds per square inch) at 180°F (82°C), or higher in some variants; check product label for exact ratings.
• Temperature Rating: Suitable for hot water up to 180°F (82°C) continuously, with short-term peaks up to 210°F (99°C). Not recommended for freezing conditions without insulation.
• Standards and Certifications: Meets ASTM F441/F439 for CPVC pipe and fittings, NSF/ANSI 61 for potable water, and often carries CSA or UL approvals. Imported versions may include Saudi Arabian Standards Organization (SASO) certification.
• Dimensions: Tee length (run to branch) typically 2-3 inches; weight around 0.2-0.3 lbs per piece.
• Color: Usually light gray or white for easy identification in plumbing.
• Packaging: Sold individually or in bulk; imported from Saudi Arabia, so check for origin markings.

Evidence: These specs are based on standard CPVC industry data from ASTM and manufacturer datasheets (e.g., AGM or similar brands like FlowGuard). Actual specs can vary by batch; always verify with the supplier’s documentation.

Installation

CPVC fittings like the AGM Tee are installed using solvent cement for a permanent, leak-proof joint. Follow these steps (based on ASTM D2846 guidelines):

1. Preparation: Cut the CPVC pipe squarely using a pipe cutter. Deburr and clean the ends. Ensure the fitting and pipe are dry and at room temperature (above 50°F/10°C).
2. Priming: Apply a CPVC primer to the pipe end and fitting socket for 10-30 seconds to soften the surface.
3. Cementing: Apply CPVC solvent cement evenly to both surfaces. Insert the pipe into the tee socket fully, twisting slightly (1/4 turn) for even distribution. Hold for 30-60 seconds to set.
4. Curing: Allow 24 hours for full cure before pressurizing. Support pipes to prevent sagging.
5. Tools Needed: Pipe cutter, deburring tool, primer, cement, applicator brush.
6. Safety Notes: Work in a well-ventilated area; wear gloves and eye protection. Avoid over-tightening or using on incompatible materials.

For hot water systems, ensure the system is depressurized during installation. Consult local plumbing codes (e.g., UPC or IPC) for specifics.

Usage

This tee is primarily used in hot water plumbing systems, such as:

• Residential hot water lines (e.g., connecting showers, sinks, or radiators).
• Commercial applications like hotels or offices for efficient water distribution.
• Industrial setups requiring corrosion-resistant piping for hot fluids.

It’s ideal for systems where metal pipes corrode or plastic alternatives fail under heat. Avoid use in direct sunlight, chemical exposure, or above-rated temperatures/pressures. For potable water, ensure the system is flushed after installation. Lifespan: 50+ years with proper maintenance, per manufacturer claims supported by ASTM testing.